-
CL Series High Speed Vertical Machining Center CL Series High Speed Gantry Machining Center CHS Series High-speed Removal Machining Center CS Series Gantry Machining Center CT Series Drilling & Milling Machining CenterCP Series Five-axis Horizontal Swing Head Machining Center GF Series Five-axis Fixed Beam Gantry Machining Center CBS Series Five-axis Bridge Machining Center CV Series Five-axis Vertical Machining Center A Series Five-axis Horizontal Cradle Machining Center C Series Five-axis Column Vertical Machining Center GE Series Five-axis Crane Machining Center
1. Remember the serial number (program line number) when the program stops halfway. In case of power failure, the line number cannot be remembered. After restarting, you can view the power-off serial number value in the processing parameter setting screen.
2. On the execution processing page, move the cursor to the serial number column.
3. Enter the serial number when the program stops halfway.
4. After confirming that the serial number is entered correctly, press Enter, and a break point will appear to find and confirm again.
5. Before executing the program, select the hand wheel simulation mode.
6. Start the program and shake the handwheel to confirm whether the break point is correct.
7. After determining the safe processing, the program is automatically processed.
1. The shortest tool length to be used on the spindle.
2. Use the handwheel to move the tool to the side of the tool-set instrument. The shortest tool tip is 0.1~0.2mm lower than the plane of the tool-set instrument.
3. Record the Z-axis mechanical coordinates of the current machine tool.
4. Enter the automatic tool setting screen and compare the H value of the lowest mechanical coordinate of the Z axis with the value in (3). The greater the negative value, the greater the distance allowed to move down the Z axis.
5. After modifying the H value of the lowest mechanical coordinate of the Z axis, restart the automatic tool setting.
6. When the tool setting coordinates are modified each time, please use the hand wheel simulation method to carry out the tool setting inspection. After the safe use is confirmed, the tool can be automatically set.
1. Check which axis "over hardware alarm" is displayed on the display screen ".
2. Press and hold the OTREL key (the red key between panel X + and X-) while moving the axis passing through the hardware in the other direction. For example, the machine tool alarm "Y axis over positive hardware stroke", press and hold the OTREL key, and at the same time use the handwheel to move in the negative direction of the Y axis to solve the alarm, or press and hold the Y-key to cancel the alarm.
3. In order to better protect the machine tool, it is recommended to use handwheel mode to solve the alarm or be sure to adjust the magnification gear to 10%.
1, check the knife cylinder, booster cylinder, nitrogen cylinder, oil cooler, oiling machine, etc. whether the amount of oil is sufficient.
2. Manually inject guide rail oil to lubricate the guide rail.
① There is a button next to the indicator light on the oiling machine. In the emergency stop state, press and hold the button, let the oiling machine stay for 5 seconds when the pressure rises to 1.5Pa, then release it, and repeat the oiling for 2 to 3 times.
② On the control panel, press the oiling button, and when the button light is on, the oiling machine will automatically oil. After the key light goes out, press this key again and repeat the oil for 2~3 times.
3. The machine tool returns to the origin.
4. Manually loosen the clamp.
5. Tool change for tool magazine hole.
6. Write a heat engine program and run the heat engine for half an hour. (Recommended spindle speed around S1000 rpm, feed rate F1000 mm/min,)
Take CTL-800 machining center as an example, heat machine reference program:
G90 G54
S1000 M03
G53 X0 Y0 Z0
G53X-800. Y-500. Z-450.
M99
1. To cancel the alarm, it is necessary to shut down the machine, and it is necessary to cut off the total power supply of the machine tool for one minute before restarting the machine tool.
2. If the machine tool is restarted and the alarm is still not lifted, please contact our sales and service personnel for on-site inspection and resolution. 0769-82280081 to 869 after-sales service department.
1, the alarm is to remind the user to confirm the processing data, better protect the customer's product processing, to avoid accidental loss of data processing waste.
2. The customer only needs to restart the machine tool again and the alarm will be released by itself.
1. Check which axis the monitor shows the alarm.
2. Open the electric box door and find the corresponding driver.
① For machining center machines and drilling and tapping machines, the driver is at the top left of the distribution board, and the corresponding order of XYZ axis is: first from left to right, then from bottom to top.
② Engraving and milling machine, the driver is at the bottom left of the distribution board, and the corresponding order of the XYZ axis is: from left to right.
3. Check the driver screen to display the alarm code in the form of 8-character code. General alarms include AC9, A10, A84, etc.
4. Please copy down the alarm code of the driver and contact our sales and service personnel. We will solve the problem for you as soon as possible. 0769 -82280081 to 869 after-sales service department.
1, the alarm for the oil cooler power supply reverse phase or lack of phase fault.
2. After shutdown and power off, switch any two phases in the three-phase power line to each other, and then turn on to observe whether it is normal.
3. If the situation is improved, please use a multimeter to check whether the three-phase power of the oil cooler is 220V. If there is a lack of phase, please check the circuit.
official micro signal
Mobile phone official website
Online Message
Leave your contact information and needs, we will arrange for professionals to contact you
Quick Navigation
Contact Us
Add.: No.1, Dongye Road, Houjie Town, Dongguan City, Guangdong Province, China
Tel: +86-769-38825288
Fax: +86-769-38825138
E-mail: sale@catocnc.com
Web: http://www.catocnc.com
Service Hotline: +86-400-680-6638